Swagelok fittings tightening instructions. Tools, steps to assemble a Swagelok tube fit...
Swagelok fittings tightening instructions. Tools, steps to assemble a Swagelok tube fitting. For 1/16, 1/8, and 3/16 in. If the gauge will enter the gap, additional Additional regional languages may be available on your local Swagelok Sales and Service Center's websites. After swaging: Apply the enclosed lubricant sparingly to the . Do not bleed system by loosening fitting nut or fitting plug. This technical bulletin is issued to provide information on proper installation and make-up of Swagelok® tube fittings. Safe practices and proper installation are imperative to the performance of the Swagelok Insert tubing into the Swagelok tube fitting. Make sure that the tubing rests firmly on the shoulder of the tube fitting body and that the nut is finger-tight. Disassembly before use is See the instructions starting below for installation of Swagelok tube fittings, O-seal male connectors, caps and plugs, port connectors, tube adapters, positionable elbows and tees, weld fittings, depth At Swagelok, we provide quality components and encourage our customers to train their installers on proper installation, including tubing selection and preparation, as well as the Swagelok tube fitting While holding fitting body steady, tighten the nut one-quarter turn. ; 2, 3, and 4 mm tube fittings, tighten the nut one-eighth turn. Get a pocket guide and Installation Instructions Over 1 in. SwagelokTM instructions (for metal ferrules) When assembled correctly, SwagelokTM fittings form a leak tight seal and can be re-tightened many times. Do not use the Swagelok gap inspection gauge with While holding fitting body steady, tighten the nut one-quarter turn. While holding Swagelok Tube Fittings Mark the nut at the 6 o’clock position. Make sure that the tubing rests firmly on the shoulder of the tube fitting body These instructions apply both to traditional fittings and to fittings with the advanced back-ferrule geometry . The Tube Fitter's Manual contains information on specifying Swagelok tube fittings and proper installation and use of high-quality tubing. Fully insert the tube See the instructions starting on the next page for installation of Swagelok tube fittings, O-seal male connectors, caps and plugs, port connectors, tube adapters, positionable elbows and tees, weld Note: Make all connections with two wrenches, do not allow the fittings to turn or twist when tightening. Do not use the Swagelok gap inspection gauge with Swagelok’s tube fittings are developed with such stringent control over all variables that a gap inspection gauge can be used to ensure proper tightening when the fittings are first installed. It These instructions apply to both traditional fittings and to fittings with the advanced back-ferrule geometry. The position of the ferrule sets This guide includes instructions for safe practice and installation of Swagelok tube fittings, O-seal male connectors, caps and plugs, port connectors, tube Subject: Swagelok® Tube Fittings - Tightening Instructions. or 25 mm and under Swagelok tube fittings come to you completely assembled, finger-tight and are ready for immediate use. Fully insert the tubing into the fitting and against the shoulder; rotate the nut finger-tight . ; 2, 3, and 4 These instructions apply both to traditional fittings and to fittings with the advanced back-ferrule geometry. You are leaving the Swagelok Calgary site for the Swagelok corporate site. Tube Fitting Installation and Reassembly Safety Instructions Up to 1 in. Do not assemble and tighten fittings when system is pressurized. The combination of these Swagelok’s tube fittings are developed with such stringent control over all variables that a gap inspection gauge can be used to ensure proper tightening when the fittings are first installed. Tighten Swagelok fittings to a torque spec, not infinite tightness. If the gauge will not enter the gap, the fitting is sufficiently tightened. Swagelok® tube fittings Installation Instructions Swagelok tube fittings 1 in. Insert the tube with pre-swaged ferrules into the fitting until the front ferrule seats against the fitting body; rotate the nut finger-tight. While holding the fitting body steady, tighten the nut 1 and 1/4 turns to the 9 o’clock position. Scribe the nut at the 6 o’clock position. Mark the nut at the 6 o’clock position. Apply the lubricant packaged with the Position the Swagelok gap inspection gauge next to the gap between the Nut and Body. /25 mm These instructions apply both to traditional fittings and to fittings with the advanced back-ferrule geometry. Fully insert the tube into the fitting and against the shoulder; rotate the nut finger-tight. / 25 mm Swagelok® Tube Fittings Preswage the ferrules onto the tube using a Swagelok multihead hydraulic swaging unit (MHSU). For additional Use the Swagelok multihead hydraulic swaging unit (MHSU) in accordance with its furnished instructions to swage the ferrules onto the tubing. Note: For 1/16, 1/8, and 3/16 in. See how the two-ferrule design can be disassembled and reassembled. While holding the fitting body steady, How To Tighten Swagelok Fittings? This video provides a step-by-step guide on how to properly install a ¼- to 1-inch tube fitting using Swagelok. blfpaj ehwjo ytb bteg jdja rjvc xaryebcg sba zwo giid
